行業新聞

聯系我們

conww.jpg

公司: 山東綿邈園林景觀工程有限公司

聯系人:于經理

手 機: 18354188859

地址:山東省濟南市高新區天辰路979號辦公樓1-101

行業新聞

您的當前位置: 首頁>新聞動態>行業新聞>玻璃鋼雕塑主要的三類模具材料介紹

玻璃鋼雕塑主要的三類模具材料介紹

發布日期: 2019-04-01 來源:http://www.nakagawakousan.com 點擊: 發布人:admin

玻璃鋼抽象雕塑是通過人們的靈感想法來創作的一種,這種雕塑不規則,不像動物雕塑那樣固定的模式,這種雕塑讓人們聯想到的更多,也可以說是每一個人對某一種抽象事物的理解,因此這種雕塑可以給大家一些啟示。山東景觀雕塑公司補充的一點就是,這一種雕塑與環境的結合也讓城市變得更加擁有色彩,更加的生動。

FRP abstract sculpture is a kind of creation through people's inspiration. This kind of sculpture is irregular, unlike the fixed pattern of animal sculpture. This kind of sculpture makes people associate more with it. It can also be said that everyone understands an abstract thing. Therefore, this kind of sculpture can give you some inspiration. Shandong Landscape Sculpture Company adds that this combination of sculpture and environment also makes the city more colorful and lively.
玻璃鋼雕塑模具材料主要有三類:
There are three main types of FRP sculpture mould materials:
1、用玻璃鋼資料做成的模具型腔,也叫硬模法。也就是在玻璃鋼模具上翻制玻璃鋼雕塑,玻璃鋼模具普通采用手糊成型辦法,制造前應設計成型線路。
1. The die cavity made of FRP material is also called hard die method. That is to say, the FRP sculpture is turned over on the FRP mould. The hand paste forming method is commonly used in the FRP mould, and the forming circuit should be designed before manufacture.
2、石膏資料做成的模具型腔,也叫碎模法。但石膏資料強度低、放置時間長時容易變形。
2. The mold cavity made of gypsum material is also called broken mold method. However, the gypsum material is of low strength and easy to deform for a long time.
3、硅橡膠資料做成的模具型腔,也叫軟模法。硅橡膠資料運用前為流體狀態,活動性及填充性好。配制后經交聯反響構成橡膠彈性體,可具有較大的彈性變形。交聯后的硅橡膠密封性好,與原模及玻璃鋼皆不粘接。用其做玻璃鋼雕塑模具的外表層資料,既能夠高質量地復制出作品的外形,又能夠保證順利脫模。但是,硅橡膠交聯體容易變形,在用作模具時,需有支撐載體。能夠應用玻璃鋼易成型的特性,用作模具的載體資料。詳細的模具制造辦法是:將配制好的硅橡膠分幾次涂劇在原模上,硅橡膠層應在1mm后以上。待硅橡膠交聯后,在硅橡膠上再成型厚度為3mm左右的玻璃鋼層。玻璃鋼固化后,沿著劃分出的單元塊將整體模具切開,切割時留意將玻璃鋼層及硅橡膠層同時切開。
山東景觀雕塑產品展示
在單元塊間制造銜接肋,銜接肋處應設定位槽,以保證經過銜接肋使單元塊模具組合成一整體。以上工作完成后,將玻璃鋼單元塊脫模,然后脫下硅橡膠層,脫下的硅橡膠塊立刻放回玻璃鋼單元模中。
3. Mold cavity made of silicone rubber material is also called soft mould method. Silicone rubber data were in fluid state before application, with good mobility and filling. The rubber elastomer can be formed by cross-linking reaction after preparation, which can have large elastic deformation. The cross-linked silicone rubber has good sealing property and does not bond with the original mould and FRP. Using it as the surface material of FRP sculpture mould can not only reproduce the appearance of the work with high quality, but also ensure the smooth demoulding. However, the cross-linking of silicone rubber is easy to deform, so it needs support carrier when it is used as a die. It can be used as the carrier material of the mould by using the easy-forming property of FRP. Detailed die manufacturing method is: the prepared silicone rubber is painted on the original model several times, and the silicone rubber layer should be more than 1 mm later. After crosslinking of silicone rubber, the fiberglass reinforced plastic (FRP) layer with a thickness of about 3 mm was formed on the silicone rubber. After FRP solidification, cut the whole die along the dividing blocks. When cutting, pay attention to cutting both FRP layer and silicone rubber layer at the same time. The joint ribs are manufactured between the units, and a slot should be set at the joint ribs to ensure that the unit die is combined into a whole through the joint ribs. After the above work is completed, the FRP unit block is demoulded, then the silicone rubber layer is removed, and the removed silicone rubber block is immediately put back into the FRP unit die.
看了以上的內容,不知道大家是不是都明白了呢。今天的精彩內容由山東景觀雕塑公司友情提供,希望對大家有所幫助,更多的精彩內容歡迎咨詢我們的官網:http://www.nakagawakousan.com
After reading the above, I wonder if you all understand it. Today's wonderful content is provided by the friendship of Shandong Landscape Sculpture Company. I hope it will be helpful to you. More wonderful content is welcome to consult our official website: http://www.nakagawakousan.com.

在線客服
分享
免费a片在线观看_欧美丰满熟妇xxxx性ppx_中文字幕无码日韩欧毛_国产精品综合av一区二区_国产欧美日韩一区二区搜索